John Sayers' Recording Studio Design Forum
http://johnlsayers.com/phpBB2/

Devils Hollow - Bridgetown - Western Australia
http://johnlsayers.com/phpBB2/viewtopic.php?f=11&t=20111
Page 1 of 1

Author:  John Sayers [ Sun Aug 16, 2015 3:41 pm ]
Post subject:  Devils Hollow - Bridgetown - Western Australia

Construction is well under way for Devil's Hollow, a full studio with accommodation. Built on 10 acres.

here's a walk through video.

http://johnlsayers.com/Video/devils_hollow.mp4

Attachment:
IMG_2999.jpeg


Attachment:
IMG_3049.jpeg


Attachment:
IMG_3131.jpeg

Author:  Soundman2020 [ Mon Aug 17, 2015 1:53 pm ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

Very nice looking place, John! Spacious and airy. Nice work!

Can't wait to see more progress photos!

- Stuart -

Author:  John Sayers [ Mon Aug 17, 2015 6:51 pm ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

Here are the views of the building.

I designed the whole building from the ground up and my plans were submitted to council for approval, which was granted.

I had a structural engineer design the trusses etc.

Attachment:
Michael_1.jpg


Attachment:
Michael_2.jpg


Attachment:
Michael_3.jpg


Attachment:
Michael_4.jpg


Attachment:
Michael_5.jpg

Author:  John Sayers [ Sun Sep 06, 2015 12:32 pm ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

Attachment:
IMG_0068.jpeg


Attachment:
IMG_0112.jpeg


Attachment:
IMG_0115.jpeg


Attachment:
IMG_5896.jpg

Author:  Soundman2020 [ Mon Sep 07, 2015 1:25 pm ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

That's progressing pretty fast, John. And it looks to be very spacious. Can't wait to see the finished product!

- Stuart -

Author:  sonicheavenstudios [ Mon Aug 15, 2016 10:44 pm ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

thats huge

nearly the size of my house.

Looks Great!! 8)

Author:  Gregwor [ Sat Mar 31, 2018 8:18 am ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

Any updates on this place? I can't even find it on Google.

Greg

Author:  cryptonym [ Sat Jun 23, 2018 5:20 pm ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

Happy to inform that after a long break building has recommenced on my studio. I'm concentrating on the control room so am getting to the good bit! Here's a few progress shots.

Attachment:
outside.jpeg

Attachment:
control front.jpeg

Attachment:
bulkhead.jpeg

Attachment:
pano.jpg

Attachment:
framing prior to sheeting.jpg


I'm about to run some cable for power to the main monitors so the boys can finish off the soffit mount area/whole front end, so here's a question for you learned folk; Would one dedicated circuit for the pair of speakers be OK (from a ground loop hum perspective), or run a dedicated circuit for each speaker?
Another minor point that you may be able to shed light on, does the orientation of the acoustic hangers hanging under the soffits and window matter much? i.e. hanging perpendicular to front, diagonal/45 degrees etc.
Thanks for the interest so far. Happy to post more pics... :D
Mike

Author:  Soundman2020 [ Sun Jun 24, 2018 3:36 am ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

Quote:
Would one dedicated circuit for the pair of speakers be OK (from a ground loop hum perspective), or run a dedicated circuit for each speaker?
Do you have another method for powering them off individually? If so, then no problem: out them both on one circuit. But if you will not be able to reach the power switches on the rear panel after they are fully soffit mounted, then I'd go with separate circuits. You never know when you'll need to power down just one speaker while the other runs. For example, while testing and fine-tuning your room: viewtopic.php?f=3&t=21122

Quote:
does the orientation of the acoustic hangers hanging under the soffits and window matter much?
IT does, to a certain extent. Tom Hidley used to orient all of his hangers towards the speakers (edge-on), but I don't see the need for that, and the ones UNDER the speaker are already edge.on from above anyway! However, if you think of hangers as acting like waveguides (they do), then think about the frequencies they are dealing, and the direction from which the wave fronts will be approaching, that will give you some insight into which way to orient them. I like to have them angled a bit "off" from being edge-on to the wave front, but certainly not straight across it: no more than about 30° or so, to ensure that the waves are actually "guided" into the thick insulation at the rear and sides of the hanger area.

There's also the issue of frequency: the larger the dimensions of the hanger, the lower it goes in treatment. If you angle it, you can make it longer (front to back) than if you have it at 0° or 90°. So the more you angle it, the longer it can be, and therefore the lower it will go.

However, having said all that, since John designed your place, you should check with him on those details. He might have valid reasons for doing things differently- Follow his advice, and the plans he surely gave you, for all of the acoustic stuff. He's the designer, so he knows why he did what for each part of the treatment.

Your place is looking great, by the way!


- Stuart -

Author:  cryptonym [ Sun Jun 24, 2018 11:46 am ]
Post subject:  Re: Devils Hollow - Bridgetown - Western Australia

Thanks Stuart - and yes will do. I have so many little questions I don't like to pester! Thanks also for the link - I haven't yet got through all 15619 topics on this awesome forum yet.

Page 1 of 1 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/